There are two main types or styles of throw out bearings (TOB) for a Nissan Skyline, push and pull. There is a third style that isn’t OEM for these cars, but is used OEM on many later cars which is a hydraulic throw out bearing.
If you are swapping or changing parts on a push style transmission. You should always check for free play. Free play is the distance between the clutch face and the throw out bearing. If you have too much free play the clutch will not disengage. If you have too little, the clutch will always slip and you will burn it out. Ask me how I know about that last part. I have installed clutches, not checked free play, and hurt the clutch just cruising around. Don’t be like me. Check and see. Many aftermarket clutches require a different throw out bearing. Know what clutch you have, and what the manufacturer recommends. If you don’t have instructions, then you are going to have to ask the Google.
![]() |
| OEM R32 GT-R early clutch. Notice clutch fingers. This is a push clutch |
Factory Clutch and Throw Out Bearings For Nissan Skyline
![]() |
| Late R32 bellhousing. This has bosses for push and pull clutch. It is currently a push clutch, or early. |
R32 GTR
Disc- C0100-05U15
Cover-30210 – 05U01
Throw Out Bearing Push- 30502-21000
Koyo RCT4075-1S (Replacement for 30502-21000)
NSK 40TRK1 (Replacement for 30502-21000)
Disc- 30100-0V708
Cover- 30210-24U00
Bearing- 30502-12U00
Late Pull Slave Cylinder assembly -30620-12U0A
Bearing Sleeve- 30501-S0200 (18mm)
Supersession(s): 13021-B9500; 13022-B9500; 13023-B9500; 15041-B9500; 15043-B9500; 32202-30000; 32202-B9500; 32202B950A
Flywheel –12310-05U10(earliest part number. Supersedes to 12310-05U16). All the push and pull use the same flywheel. As does the RB20.
![]() |
| 12310-05U13 which fits pull/late R32 and early R33 according to part number. Then superseded to 05U14 and then 05U16. |
| Nissan Skyline throw out bearing carrier. These are available in many different heights. It is important to check free play |
30501-22102 8mm
30501-B5000 10mm (superseded to 30501-B5004)
30501-A3800 12mm
30501-N1601 14mm
30501-U0200 16mm
30501-S0200 18mm
Clutch Pedal Adjustment for Nissan Skyline GT-R
| The clutch pedal may also need some adjustment. This is the procedure from the service manual |
The clutch pedal adjustment on the R32,R33, R34 Skyline takes a 7mm wrench. Its sort of an oddball and in a tough spot. So if you need to adjust it, make sure you warm up with some yoga first.
| Wera 7mm wrench used to adjust the clutch pedal height on a Nissan Skyline |
| OS Giken TOB sleeve recommended lengths. |
All the early cars have push style clutches. That is 1989- Jan 1993. However, it is 2019. You don’t know what happened in your cars life. If you blindly chose parts without checking, you are probably in for a rude awakening. Look at the car, its pretty easy to check, and know if your car is push or pull clutch. You don’t want to find that out, after you have ordered parts from Japan, have the transmission out, and realize you have the wrong part. The later transmission bellhousings normally have both bosses on them for either throw out bearing. However the early transmissions do not have the later bosses on them.
![]() |
| This is a conversion kit from OS Giken to convert a pull style transmission to a push style clutch. |
| Hydraulic throw out bearing and a Tilton triple plate carbon clutch. This is a big boy clutch |
![]() |
| Hydraulic throw out bearing on a Getrag transmission |
| How to release a pull style throw out bearing |
![]() |
| Pull style clutch. Notice ring at center |
![]() |
| Showing throw out bearing for a pull clutch |
Nissan Skyline GT-R Transmission information
Clutch
Clutch Weights
How to install a 6 speed Getrag in a R32/R33 GT-R
Buy USA Legal R32 and R33 Skylines at Importavehicle.com!
Buy-R.com for Nissan Skyline GT-R and GT-R parts.




































Leave a Reply